COTE-L’S CEASEFIRE FLAME PREVENTATIVE

  COTE-L Home Page
  CF Basic Data Sheet
  CF High Performance
  CEASEFIRE Instructions
  CF Industrial
  CFHP White Epoxy Specs
  CF White Epoxy
  CFHP Clear




TWO-PART EPOXY PRODUCTS

Description:

Unique two-part, solvent-less 100% epoxy coatings containing COTE-L’s state-of-the-art Flame Preventative Intumescent CEASEFIRE™ additive.

Products:

  1. CEASEFIRE™ HIGH PERFORMANCE TWO-PART WHITE EPOXY COATING has passed flame spread and toxicity tests (at very low levels) and is DNV and ABS certified for use on ships and mobile off-shore units in all areas, including ceilings, bulkheads and floors. It is used in such areas as stairwells, walls, ceilings, doors, kitchen areas and areas which need to be cleaned on a regular basis. It performs exceptionally well on steel, masonry, wood and plastics in industrial settings, as well as domestic applications.

  2. CEASEFIRE™ SUPERIOR TWO-PART WHITE EPOXY COATING has most of the same properties as the CEASEFIRE™ High Performance Two-Part White Epoxy Coating, but has a higher viscosity, dries to a matte finish and is only necessary when required to meet stricter thermal conductivity codes. It cures to a firm hardness and is used in such applications as structural steel beams, industrial pipes, train interiors, etc.

  3. CEASEFIRE™ HIGH PERFORMANCE TWO-PART CLEAR EPOXY COATING is used to protect wood or any other surfaces where a clear high-gloss fire retardant finish is needed. It has been specified to protect ancient oriental wooden shrines, as well as wood trim on naval vessels.

Properties:

CEASEFIRE™
TWO-PART EPOXY COATINGS
HIGH PERFORMANCE
Color: White
SUPERIOR
Color: White
HIGH PERFORMANCE Color: Clear
Can Be Tinted
  • Cures to a very tough, chip-resistant finish
  • Can be used indoors and outdoors
  • The Clear will yellow over time outdoors but will not breakdown.
    Insoluble in water
  • Can be thinned with solvents
  • Finish High Gloss Matte High Gloss
    Low smoke generation
  • Very low smoke toxicity
  • Char activation temperature 300oC 300oC 250oC
    Char swells up to 1.5" 1.5" .5"
    Provides very efficient flame barrier
  • Can be applied by roller, brush or spray
  • High thermal insulation
  • Superior chemical resistance
  • Excellent adhesion to metal, masonry, wood and plastics
  • Excellent impact resistance
  • Washable
  • Highest quality pure epoxy (bisphenol A)
    [has high structural integrity – not based on epoxidized oils]
  • To repair: clean surface and recoat anytime
  • Apply to clean dry surface
  • Working life ± 4 hours at 77oF
  • Tack-free set time at ± 77oF 12 hours 12 hours 12 hours
    48-hour full cure
  • Contains very low load levels of CEASEFIRE™ additive, which allows for a thinner coating with superior performance to the competition. Low load level does not impede performance of the coating.
      (Note: in order to produce fire retardant properties, competitive products add large amounts of minerals, sugars or starches, thus necessitating higher material costs, labor intensity to install and limits on useability.)
  • Percentage Solids 100% 100% 100%
    Mix Ratio (A:B) 100:20 100:20 100:26
    Mix Viscosity @ 77oF 35,000 cps 8,600 cps Part A:
    1600 cps
    Part B:
    200 cps
    Flammability Rating (UL94) V - 0 V - 0 V - 0
    Glass Transition Temperature 80oC 80oC 70oC
    Hardness Shore D 72
  • Peel Strength 6.5 lbs/inch
  • Elongation at Break 12% 12% 12%
    Thermal Conductivity of Char very low very low very low
    Air Convection Through Char .001cc(mmHg)
    am2 sec
    .001cc(mmHg)
    am2 sec
    x
    CEASEFIRE™
    TWO-PART EPOXY COATINGS
    HIGH PERFORMANCE
    Color: White
    SUPERIOR
    Color: White
    HIGH PERFORMANCE Color: Clear
    Spread Rate (final spread rate depends on thickness needed):

    • One coat on sealed wood, 5 mils;
    • Two coats on unsealed wood, 5 mils
    • 150 SF/Gal @ 10 mils thick
    x x

    • 5 mils = 300 SF/Gal
    • 10 mils = 150 SF/Gal
  • x x

    • 15 mils = approx. 110 SF/Gal
    x
  • x
    CEASEFIRE™
    TWO-PART EPOXY COATINGS
    HIGH PERFORMANCE
    Color: White
    SUPERIOR
    Color: White
    HIGH PERFORMANCE Color: Clear
    Stops flame spread and minimizes smoke generation and smoke toxicity to the following specifications:
      ASTM E84 Flame Spread test rating
      (Class “A” flame spread req. 25 or below)
    5 5 10
      ASTM E84 Smoke Density test rating
      (Class “A” smoke density requires 450 or below)
    5 5 10
      DNV Certified for I.M.O. (International Marine Organization) MSC.41 (64) Smoke and Toxic Products of Combustion. CEASEFIRE™ rate an average of 96% below minimum allowable level of toxicity.
    YES YES NOT YET TESTED
      Preliminary ASTM E119 Fire Endurance Screening Testing on 1/2" thick coated steel (60 minutes required to meet standard)
    74 min. in preliminary tests NOT YET TESTED NOT YET TESTED



    Cote-L Home Page
    CEASEFIRE™ Data Sheet
    DURABAK™ Spec Sheet
    DURABAK™ Application Tips
    SAFTI-TRAX Information
    "Road and Bridges" Article
    ASTM Tests



    COTE-L Industries, Inc.